- Acura Engines
- Used Audi Engines
- BMW Engines
- Buick Engines
- Cadillac Engines
- Chevrolet Engines
- Used Chrysler Engines
- Dodge Engines
- Used Ford Engines
- GMC Engines
- Used Honda Engines
- Hummer Engines
- Hyundai Engines
- Infiniti Engines
- Isuzu Engines
- Jaguar Engines
- Jeep Engines
- Kia Engines
- Land Rover Engines
- Lexus Engines
- Used Lincoln Engines
- Mazda Engines
- Mercedes Engines
- Mercury Engines
- MINI Engines
- Mitsubishi Engines
- Nissan Engines
- Oldsmobile Engines
- Plymouth Engines
- Pontiac Engines
- Porsche Engines
- Saab Engines
- Saturn Engines
- Scion Engines
- Subaru Engines
- Suzuki Engines
- Toyota Engines
- Volkswagen Engines
- Volvo Engines
Engine Related Articles:
Engine and Transmission Installation Guides
**We highly recommend you use an ASE certified mechanic for your installation.
ENGINES - All engines sold under the used category must meet the following requirements to qualify for the supplier warranty. All warranties extended by the supplier are subject to terms and conditions of that supplier, NOT GotEngines.com. Used engines are understood to consist of a short block assembly and cylinder heads ONLY. Any other parts left on the used engine at the time of sale are included for possible customer convenience, but are not required to be sent by GotEngines.com or any given supplier. Those items may be used at the customer’s discretion but they are not covered by any warranty of any type. The installer should transfer all components from the original engine to this replacement engine. Any components known to be inoperable need to be replaced. Any previous issues that caused this replacement must be fixed prior to installation of this replacement engine.
1. New water pump, timing belt/chain, front and rear main seals on used and reconditioned engines must be installed.
2. Oil strainer and pick up screen must be cleaned or replaced prior to installation.
3. Thoroughly clean all units such as oil pan, timing cover, rocker arm covers, intake manifold and any other parts that may need cleaning before reassembling.
4. Replace oil filter and oil.
5. Replace tune‐up items such as plugs, cap, rotor, fuel and air filter, pcv valve, and other parts specific to the engine.
6. Check and adjust valves and timing to factory specifications.
7. Replace thermostat and test cooling system.
8. Fuel lines should be checked for debris and flow.
9. Inspect wire harness for broken wires or insulation damage.
10. Always remember to prime oil pump and oil lines.
11. Change your oil and filter after the first 500 miles and every 3000 miles thereafter.
12. Catalytic converter must be inspected to make sure it is not clogged. A defective converter can cause damage to piston rings and internal bearings.
13. Check all cooling components such as hoses, freeze plugs, radiator and coolant. Radiator should be cleaned or replaced.
14. Blow out intake ports to remove any loose particles that may fall into cylinder head and cause damage.
15. Replace all seals and gaskets regardless of condition. These include but are not limited to valve cover, oil pan, intake and exhaust manifolds, and timing cover. Seal or gasket failure is not covered under basic warranty. Damage caused by seal or gasket failure is not covered.
Engine Start‐Up Procedure:
1. Remove all spark plugs
2. Remove oil sending unit switch.
3. Crank the engine until oil comes out oil sending unit switch hole.
4. If oil won’t come out, spray the oil sending unit switch hole with oil or penetrating lubricant to prevent dry start.
5. After oil comes out, replace oil sending unit switch and crank engine for 1 to 2 minutes, until oil pressure is normal.
6. Replace spark plugs and then start engine. Do not accelerate above idle until normal oil pressure is reached.
1. After starting, cylinder head must be re‐torqued and valves re‐adjusted to manufacturer’s specifications after the engine reaches normal operation temperature and once again at 500 miles.
2. Oil and filter must be changed before start up and again after 500 miles and every 3000 miles thereafter. Receipts for lubricants, filters and service may be required. Failure to perform these operations voids warranty.
3. Follow the periodic maintenance as set forth by manufacturer’s specifications to keep your warranty in‐tact.
TRANSMISSIONS - All transmissions sold under the used category must meet the following requirements to qualify for the supplier warranty. All warranties extended by the supplier are subject to terms and conditions of that supplier, not GotEngines.com. Any previous issues that caused this replacement must be fixed prior to installation of this replacement transmission.
- Completely flush system. **Some transmissions require precise fluid type and flush procedure to prevent damage or contamination.**
- Thoroughly clean all units such as fluid pan and any other parts that need cleaning before assembly.
- For an automatic transmission, you must install a new oil cooler, new filter kit and new oil.
- Replace fluid and check level for a standard transmission.
- Replace front and rear seals.
- Check all lines and linkage for damage or blockage. Adjust linkage and cables to ensure proper shifting and operation of clearance.
- Torque converter must be replaced. If a torque converter was shipped with the transmission, it is ONLY to protect it during shipping. Make sure it is properly aligned in the pump assembly and filled with fluid prior to start up.
- External sensors and electrical parts and operations are customer responsibility at installation. This includes coding and flashing if required.